收藏本站
Si4421
CONTROL INTERFACE
Commands to the transmitter are sent serially. Data bits on pin SDI are shifted into the device upon the rising edge of the clock on
pin SCK whenever the chip select pin nSEL is low. When the nSEL signal is high, it initializes the serial interface. All commands
consist of a command code, followed by a varying number of parameter or data bits. All data are sent MSB first (e.g. bit 15 for a 16-
bit command). Bits having no influence (don’t care) are indicated with X. Special care must be taken when the microcontroller’s built-
in hardware serial port is used. If the port cannot be switched to 16-bit mode then a separate I/O line should be used to control the
nSEL pin to ensure the low level during the whole duration of the command or a software serial control interface should be
implemented. The Power-On Reset (POR) circuit sets default values in all control and command registers.
The receiver will generate an interrupt request (IT) for the microcontroller - by pulling the nIRQ pin low - on the following events:
? The TX register is ready to receive the next byte (RGIT)
? The RX FIFO has received the preprogrammed amount of bits (FFIT)
? Power-on reset (POR)
? RX FIFO overflow (FFOV) / TX register underrun (RGUR)
? Wake-up timer timeout (WKUP)
? Negative pulse on the interrupt input pin nINT (EXT)
? Supply voltage below the preprogrammed value is detected (LBD)
FFIT and FFOV are applicable when the RX FIFO is enabled. RGIT and RGUR are applicable only when the TX register is enabled. To
identify the source of the IT, the status bits should be read out.
Timing Specification
Symbol
t CH
t CL
t SS
t SH
t SHI
t DS
t DH
t OD
Parameter
Clock high time
Clock low time
Select setup time (nSEL falling edge to SCK rising edge)
Select hold time (SCK falling edge to nSEL rising edge)
Select high time
Data setup time (SDI transition to SCK rising edge)
Data hold time (SCK rising edge to SDI transition)
Data delay time
Minimum value [ns]
25
25
10
10
25
5
5
10
Timing Diagram
nSEL
t SS
t SHI
t CH
t CL
t OD
t SH
SCK
t DS
t DH
SDI
SDO
BIT 15
FFIT
BIT 14
FFOV
BIT 13
BIT 8
CRL
BIT 7
AT S
BIT 1
OFFS(0)
BIT 0
FIFO OUT
13
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
F2M03G-KIT-1 KIT EVAL G MOD SNGL (NO OEM BRD)
F2M03M-KIT-1 KIT EVAL M MOD SNGL (NO OEM BRD)
FA10323_K2S-W LENS FOR LUXEON K2
FA10539_SSS-W LENS FOR SEOUL P4
FA10643_TINA-M LENS FOR GOLDEN/PLATINUM DRAGON
FA10644_TINA-D LENS TINA DIFF 6.5DEG
FA10666_CXP-D LENS CXP DIFF SQ 16DEG
FA10678_CMC-SS LENS CMC SMOOTH SPOT MC-E
相关代理商/技术参数
EZLC-4421HB 制造商:Silicon Laboratories Inc 功能描述:EZLink 4421 development kit, 868/915MHz
EZLC-4421LB 制造商:Silicon Laboratories Inc 功能描述:EZLink 4421 development kit, 433MHz
EZLC4431B1-D434 功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 434MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC4431B1-D868 功能描述:射频开发工具 EZLink Kit F930 Si4431 Rev B1 868MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC-4432 HB 功能描述:射频开发工具 EZLink Fast Prototype Kit Hiband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC-4432 HB/LB KIT 制造商:Silicon Laboratories Inc 功能描述:
EZLC-4432 LB 功能描述:射频开发工具 EZLink Fast Prototype Kit Lwband RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
EZLC4432B1-D470 功能描述:射频开发工具 EZLink Kit F930 Si4432 Rev B1 470MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V